View AR0833CS3C12SUAA0-DP_8945986.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? semiconductor components industries, llc, 2011 march, 2017 ? rev. 10 1 publication order number: ar0833/d ar0833 ar0833 1/3.2\inch 8 mp cmos digital image sensor table 1. key performance parameters parameter typical value array format 3264 2448 primary modes full resolution: 4:3 ? 8 mp at 30 fps 16:9 ? 6 mp at 30 fps 16:9 ? 1080p hd at 30 fps pixel size 1.4 m back side illuminated (bsi) optical format 1/3.2-inch die size 6.86 mm 6.44 mm (area: 44.17 mm 2 ) input clock frequency 6 ? 27 mhz interface mipi csi ? 2 (2 ? , 3 ? , 4 ? lane modes supported.) 800 mbps max mipi clock speed per lane. subsampling modes x ? bin2, sum2 skip: 2 , 4 y ? sum2, skip: 2 , 4 , 8 output data depth 10 bits raw or 8/6 ? bit dpcm analog gain 1 , 2 , 3 , 4 , 6 , 8 high quality bayer scalar adjustable scaling up to 1/6x scaling temperature sensor 10-bit, single instance on chip, controlled by two-wire serial i/f vcm af driver 8-bit resolution with slew rate control 3 ? d support frame rate and exposure synchronization supply voltage analog 2.5 ? 3.1 v (2.8 v nominal) digital 1.14 ? 1.3 v (1.2 v nominal) pixel 2.5 ? 3.1 v (2.8 v nominal) otpm read 1.7 ? 1.9 v (1.8 v nominal) i/o 1.7 ? 1.9 v (1.8 v nominal) or 2.5 ? 3.1 v (2.8 v nominal) mipi 1.14 ? 1.3 v (1.2 v nominal) power consumption 340 mw at 30 fps, 8 mp responsivity 0.6 v/lux-sec snr max 36 db dynamic range 64 db operating temperature range (at junction) ? t j ? 30 c to +70 c features ? high-speed sensor supporting 8 mp (4:3) 30 fps still images and full hd 1080p30 video ? 1.4 pixel with on semiconductor a-pixhs ? technology providing best-in-class low-light performance. ? optional on-chip high-quality bayer scaler to resize image to desired size www. onsemi.com features (continued) ? data interfaces: two-, three-, and four-lane serial mobile industry processor interface (mipi) ? bit-depth compression available for mipi interface: 10-8 and 10-6 to enable lower bandwidth receivers for full frame rate applications ? on-chip temperature sensor ? on-die phase-locked loop (pll) oscillator ? 5.6 kb one-time programmable memory (otpm) for storing module information ? on-chip 8-bit vcm driver ? 3d synchronization controls to enable stereo video capture ? interlaced multi-exposure readout enabling high dynamic range (hdr) still and vide o applications ? programmable controls: gain, horizontal and vertical blanking, auto black level offset correction, frame size/rate, exposure, left?right and top?bottom image reversal, window size, and panning ? support for external mechanical shutter ? support for external led or xenon flash applications ? smart phones ? pc cameras ? tablets see detailed ordering and shipping information on page 2 of this data sheet. ordering information clcc48 10 10 case 848aj
ar0833 www. onsemi.com 2 table 2. modes of operation and power consumption at 100% fov mode active readout window (col row) sensor output resolution (col row) mode fps power consumption [mw] (note 5) snapshot mode full resolution 4:3 ? 8 mp (note 1) 3264 x 2448 3264 x 2448 full mode 30 340 full resolution 16:9 ? 6 mp (note 1) 3264 x 1836 3265 x 1836 full mode 30 323 4:3 video mode vga (note 2) 3264 x 2448 640 x 480 scaling 30 293 vga (note 3) 3264 x 2448 640 x 480 bin2 + scaling 30 270 vga 3264 x 2448 640 x 480 bin2 + scaling 60 293 16:9 video mode 1080p (note 2) 3264 x 1836 1920 x 1080 scaling 30 216 1080p + eis (note 2, 4) 3264 x 1836 2304 x 1296 scaling 30 216 720p (note 2) 3264 x 1836 1280 x 720 scaling 30 216 720p (note 2) 3264 x 1836 1280 x 720 bin2 + scaling 60 295 720p + eis (note 2) 3264 x 1836 1536 x 864 scaling 30 216 wvga (note 2) 3264 x 1836 8546 x 480 scaling 30 256 wvga (note 2) 3265 x 1836 856 x 480 bin2 + scaling 60 293 1. 732 mbps/lane mipi data transfer rate 2. scaled image using internal high quality bayer scaler 3. low power preview 4. electronic image stabilization 5. values measured at t = 25 c and nominal voltages ordering information table 3. available part numbers part number product description orderable product attribute description ar0833cs3c12suaa0 ? dp 8 mp 1/3 cis dry pack with protective film see the on semiconductor device nomenclature document ( tnd310/d ) for a full description of the naming convention used for image sensors. for reference documentation, including information on evaluation kits, please visit our web site at www.onsemi.com . general description the on semiconductor ar0833 is a 1/3.2-inch bsi (back side illuminated) cmos active-pixel digital image sensor with a pixel array of 3264 (h) x 2448 (v) (3280 (h) x 2464 (v) including border pixels). it incorporates sophisticated on-chip camera functions such as mirroring, column and row skip modes, and context switching for zero shutter lag snapshot mode. it is programmable through a simple two-wire serial interface and has very low power consumption. the ar0833 digital image sensor features on semiconductor?s breakthrough low-noise 1.4 m pixel cmos imaging technology that achieves near-ccd image quality (based on signal-to-noise ratio and low-light sensitivity) while maintaining the inherent size, cost, and integration advantages of cmos. the ar0833 sensor can generate full resolution image at up to 30 frames per second (fps). an on-chip analog-to-digital converter (adc) generates a 10-bit value for each pixel.
ar0833 www. onsemi.com 3 functional overview in order to meet higher frame rates in ar0833 sensor, the architecture has been re-designed. the analog core has a column parallel architecture with 4 data paths. digital block has been re-architected to have 4 data paths. the chip is targeted to meet smia 85 module size. as a result, the final die size is 6.86 mm x 6.44 mm (singulated) which would fit in the intended module with two-sided pad frame. figure 1 shows the block diagram of the ar0833. figure 1. top level block diagram pll timing control register control two-wire serial interface row driver pixel array adc gain imaging sensor core digital processing image output 10-bit temperature sensor gain control test pattern generator data calibration digital gain scaler mipi fifo&optional compression v aa , v aa _pix v dd _io, dv dd _1v8, dv dd _1v2 mipi serial data output [3:0] external clock xshutdown gpio[1:0] gpi[3:2] s clk s data vcm vcm control dv dd _1v2_ phy ar0833 the core of the sensor is an 8 mp active-pixel array. the timing and control circuitry sequences through the rows of the array, resetting and then reading each row in turn. in the time interval between resetting a row and reading that row, the pixels in the row integrate incident light. the exposure is controlled by varying the time interval between reset and readout. once a row has been read, the data from the columns is sequenced through an analog signal chain (providing gain), and then through an adc. the output from the adc is a 10-bit value for each pixel in the array. the adc output passes through a digital processing signal chain (which provides further data path corrections and applies digital gain). the pixel array contains optically active and light-shielded (?dark?) pixels. the dark pixels are used to provide data for on-chip offset-correction algorithms (?black level? control). the sensor contains a set of control and status registers that can be used to control many aspects of the sensor behavior including the frame size, exposure, and gain setting. these registers can be accessed through a two-wire serial interface. the output from the sensor is a bayer pattern; alternate rows are a sequence of either green and red pixels or blue and green pixels. the offset and gain stages of the analog signal chain provide per-color control of the pixel data. a flash output signal is provided to allow an external xenon or led light source to synchronize with the sensor exposure time. additional i/o signals support the provision of an external mechanical shutter. pixel array the sensor core uses a bayer color pattern, as shown in figure 2. the even-numbered rows contain green and red pixels; odd-numbered rows contain blue and green pixels. even-numbered columns contain red and green pixels; odd-numbered columns contain blue and green pixels. figure 2. pixel color pattern detail (top right corner) gr b gr b r gb r gb r gb r gb gr b gr b column readout direction row readout direction first pixel (col. 0, row 60) black pixels r gb r gb note: by default the mirror bit is set, so the read-out direction is from left to right.
ar0833 www. onsemi.com 4 typical connections the chip supports mipi output protocol. mipi can be configured in 4-, 3- or 2-lanes. there are no parallel data output ports. figure 3. typical application circuit ? mipi connection 1. all power supplies should be adequately decoupled; recommended cap values are: ? 2.8 v: 1.0 f, 0.1 f, and then 0.01 f ? 1.2 v: 1 f and then 0.1 f ? 1.8 v: 0.1 f 2. resistor value 1.5 k is recommended, but may be greater for slower two-wire speed. 3. this pull-up resistor is not required if the controller drives a valid logic level on s clk at all times. 4. v aa and v aa _pix can be tied together. however, for noise immunity it is recommended to have them separate (i.e. two sets of 2.8 v decoupling caps). 5. v pp , 6 ? 7 v, is used for programming otpm. this pad is left unconnected if otpm is not being programmed. 6. v dd _1v8 can be combined with v dd _ io, if v dd _ io = 1.8 v. 7. v dd _1v2 and v dd1 _1v2_phy can be tied together. 8. atest1 can be left floating. 9. test pin must be tied to d gnd . 10. dv dd _1v8 is the otpm read voltage (must always be provided). notes: data_p data_n data2_p data2_n data3_p data3_n 2.8 v a gnd v aa 4 (pixel) v aa 4 (analog) v dd _io (io) dv dd _1v2 (digital) 7 s data s clk extclk (6 ? 27 mhz) 1.5 k 2 1.5 k 2, 3 test 8 to mipi port two-wire serial interface 2.8 v or 1.8 v xshutdown data4_n data4_p clk_p clk_n d gnd v pp 5 (otpm write) (only connected while programming otpm) atest 8 gpi[3:2] gpio[1:0] general purpose input/output dv dd _1v8 (otpm read) 6 1.2 v 2.8 v 1.2 v dv dd 1v2_phy (mipi) 7 0.01 f 0.1 f 1.0 f 1.2 v 0.1 f 1.0 f 1 1.8 v isink gnd vcm vcm vcm gnd_io gndphy dv dd _1v8 0.1 f v dd _io 0.1 f
ar0833 www. onsemi.com 5 signal descriptions ar0833 has 67 pads placed in a two sided pad frame. it has only serial outputs. the part may be configured as mipi with different bit depths. the pad description is tabulated in table 4: table 4. pad descriptions pad name pad type description sensor control extclk input master clock input; pll input clock. 6 mhz ? 27 mhz this is a smia ? compliant pad gpio0 input/output general input and one output function include: a. (default output) flash b. (input) all options in gpi2 high-z before xshutdown going high; default value is ?0? after all three voltages in place and xshutdown being high after reset, this pad is not powered down since its default use is as flash pin if not used, can be left floating gpio1 input/output general input and 2 output functions include: a. (default output) shutter b. (output) 3-d daisy chain communication output c. (input) all options in gpi2 high-z before xshutdown going high; default value is ?0? after all three voltages in place and xshutdown being high after reset, this pad is not powered-down since its default use is as shutter pin if not used, can be left floating gpi2 input general input; after reset, these pads are powered down by default; this means that it is not necessary to bond to these pads. functions include: a. s addr , switch to the second two-wire serial interface device address (see ?slave address/data direction byte?) b. trigger signal for slave mode c. standby if not used, can be left floating gpi3 input general input; after reset, these pads are powered-down by default; this means that it is not necessary to bond to these pads. functions include: a. 3-d daisy chain communication input b. all options in gpi2 if not used, can be left floating two-wire serial interface s clk input serial clock for access to control and status registers s data i/o serial data for reads from and writes to control and status registers serial output data[4:1]p output differential serial data (positive). data[4:1]n output differential serial data (negative) clk_p output differential serial clock/strobe (positive) clk_n output differential serial clock/strobe (negative) xshutdown input asynchronous active low reset. when asserted, data output stops and all internal registers are restored to their factory default settings. this pin will turn off the digital power domain and is the lowest power state of the sensor vcm driver vcm_isink input/output vcm driver current sink output. if not used, it could be left floating vcm_gnd input/output ground connection to vcm driver. if not used, needs to be connected to ground (d gnd ). this ground must be separate from the other grounds power v pp input/output high-voltage pin for programming otpm, present on sensors with that capability. this pin can be left floating during normal operation
ar0833 www. onsemi.com 6 table 4. pad descriptions (continued) pad name description pad type power (continued) v aa [7:1], v aa _pix[2:1], a gnd [9:1], v dd_ io_[4:1], gnd_io, d gnd _[6:1], dv dd _1v2_[9:1], dv dd _1v2_phy_[2:1], gndphy_[2:1], dv dd_ 1v8 supply power supply. the domains are specified in the next table. the brackets indicate the number of individual pins there are standard gpi and gpio pads, two each. chip can also be communicated to through the two-wire serial interface. the chip has three unique power supply requirements: 1.2 v, 1.8 v, and 2.8 v. these are further divided and in all there are seven power domains and five independent ground domains from the esd perspective. table 5. independent power and ground domains pad name power supply description grounds d gnd (gndphy, gnd_io) 0 v digital vcm_gnd 0 v vcm driver a gnd 0 v analog power v aa 2.8 v analog/vcm driver/otpm v aa_ pix 2.8 v pixel/analog dv dd _1v2 1.2 v digital v dd_ io 1.8 v/2.8 v io dv dd _1v2_phy 1.2 v mipi dv dd _1v8 1.8 v otpm
ar0833 www. onsemi.com 7 system states the system states of the ar0833 are represented as a state diagram in figure 4 and described in subsequent sections. the sensor?s operation is broken down into three separate states: hardware standby, software standby, and streaming. the transition between these states might take a certain amount of clock cycles as outlined in figure 4 and figure 5. figure 4. system states powered off internal initialization software standby pll lock streaming wait for frame end frame in progress pll locked two-wire serial interface write: mode_select = 1 timeout xshutdown = 1 powered on extclk cycles xshutdown = 0 pll not locked streaming two-wire serial interface write: software_reset = 1 power supplies turned off (asynchronous from any state) hardware standby two-wire serial interface write: mode_select = 0
ar0833 www. onsemi.com 8 sensor initialization power-up sequence ar0833 has three voltage supplies divided into several domains. t he three voltages are 1.2 v, 1.8 v, and 2.8 v. for proper operation of the chip, a power-up sequence is recommended as shown in figure 5. the power sequence is governed by controlled vs controlling behavior of a power supply and the inrush current (i.e., current that exists when not all power supplies are present). table 6. inrush consideration xshutdown 1.2 v 1.8 v (v dd _io) 2.8 v comment x present absent absent not supported x absent present absent supported x absent absent present supported x present present absent supported x present absent present not supported x absent present present supported 0 present present present powered down state 1 present present present powered up state since v dd _io supply controls the xshutdown, it should be turned on first. the sequence of powering up the other two domains is not too critical. while turning on 2.8 v supply before 1.2 v supply shouldn?t be an issue as shown in table 1, it is still not recommended since the 2.8 v domain is controlled by 1.2 v signals. the dedicated 1.8 v domain is used only for otpm read function, so can turn on along with 1.8 v supply. due to the above considerations, the suggested power-on sequence is as shown in figure 5: figure 5. recommended power-up sequence v dd _io, v dd _1v8 v dd _1v2, v dd _1v2_phy v aa , v aa _pix extclk xshutdown s data s clk t 0 t 1 t 2 t 3 t 4 t 5 soft standby streaming internal init hard reset first serial write pll lock
ar0833 www. onsemi.com 9 table 7. power-up sequence symbol definition minimum typical maximum unit t 0 v dd _io to dv dd _1v8 ? ? 500 ms t 1 dv dd _1v8 to dv dd _1v2/dv dd _1v2_phy 0.2 ? 500 ms t 2 sdv dd _1v2/dv dd _1v2_phy to v aa /v aa _pix 0.2 ? 500 ms t 3 active hard reset 1 ? 500 ms t 4 internal initialization 2400 ? ? extclks t 5 pll lock time 1 ? 5 ms power-down sequence the recommended power-down sequence for the ar0833 is shown in figure 6. the three power supply domains (1.2 v, 1.8 v, and 2.8 v) must have the separation specified below. 1. disable streaming if output is active by setting standby r0x301a[2] = 0. 2. after disabling the internal clock extclk, disable xshutdown. 3. after xshutdown is low disable the 2.8 v/1.8 v supply. 4. after the 2.8 v/1.8 v supply is low disable the 1.2 v supply. 5. after the 1.2 v supply is low disable the v dd _io supply. figure 6. recommended power-down sequence v dd _io v dd _1v8 v dd _1v2, v dd _1v2_phy v aa , v aa _pix extclk xshutdown s data s clk t 1 hard reset t 2 t 3 t 0 soft standby streaming turn off power supplies focal planes deactivation table 8. power-down sequence symbol definition minimum typical maximum unit t 0 extclk to xshutdown 100 ? ? s t 1 xshutdown to supply 2.8 v/1.8 v 200 ? ? s t 2 supply 2.8 v/1.8 v to supply 1.2 v 0 200 ? s t 3 supply 1.2 v to vdd_io 200 ? ? s
ar0833 www. onsemi.com 10 hard standby and hard reset the hard standby state is reached by the assertion of the xshutdown pad (hard reset). register values are not retained by this action, and will be returned to their default values once hard reset is completed. the minimum power consumption is achieved by the hard standby state. the details of the sequence are described below and shown in figure 7. 1. disable streaming if output is active by setting mode_select 0x301a[2] = 0. 2. the soft standby state is reached after the current row or frame, depending on configuration, has ended. 3. assert xshutdown (active low) to reset the sensor. 4. the sensor remains in hard standby state if xshutdown remains in the logic ?0? state. figure 7. hard standby and hard reset extclk xshutdown mode_select r0x0100 logic ?1? logic ?0? new row/frame streaming soft standby hard standby hard reset soft standby and soft reset the ar0833 can reduce power consumption by switching to the soft standby state when the output is not needed. register values are retained in the soft standby state. the details of the sequence are described below and shown in figure 8. soft standby 1. disable streaming if output is active by setting mode_select 0x301a[2] = 0. 2. the soft standby state is reached after the current row or frame, depending on configuration, has ended. soft reset 1. follow the soft standby sequence list above. 2. set software_reset = 1 (r0x3021) to start the internal initialization sequence. 3. after 2400 extclks (tentative), the internal initialization sequence is completed and the current state returns to soft standby automatically. figure 8. soft standby and soft reset extclk mode_select r0x0100 logic ?1? next row/frame streaming software_reset r0x0103 logic ?0? logic ?0? logic ?1? logic ?0? soft standby soft standby soft reset 480 2400 extclks
ar0833 www. onsemi.com 11 two-wire serial register interface a two-wire serial interface bus enables read/write access to control and status registers within the ar0833. the two-wire serial interface is fully compatible with the i 2 c standard. the interface protocol uses a master/slave model in which a master controls one or more slave devices. the sensor acts as a slave device. the master generates a clock (s clk ) that is an input to the sensor and is used to synchronize transfers. data is transferred between the master and the slave on a bidirectional signal (s data ). s data is pulled up to v dd off-chip by a 1.5 k resistor. either the slave or master device can drive s data low-the interface protocol determines which device is allowed to drive s data at any given time. the protocols described in the two-wire serial interface specification allow the slave device to drive s clk low; the ar0833 uses s clk as an input only and therefore never drives it low. the electrical and timing specifications are further detailed on ?two-wire serial register interface?. protocol data transfers on the two-wire serial interface bus are performed by a sequence of low-level protocol elements: 1. a (repeated) start condition 2. a slave address/data direction byte 3. an (a no) acknowledge bit 4. a message byte 5. a stop condition the bus is idle when both s clk and s data are high. control of the bus is initiated with a start condition, and the bus is released with a stop condition. only the master can generate the start and stop conditions. start condition a start condition is defined as a high-to-low transition on s data while s clk is high. at the end of a transfer, the master can generate a start condition without previously generating a stop condition; this is known as a ?repeated start? or ?restart? condition. stop condition a stop condition is def ined as a low -to-high transition on s data while s clk is high. data transfer data is transferred serially, 8 bits at a time, with the msb transmitted first. each byte of data is followed by an acknowledge bit or a no-acknowledge bit. this data transfer mechanism is used for the slave address/data direction byte and for message bytes. one data bit is transferred during each s clk clock period. s data can change when s clk is low and must be stable while s clk is high. slave address/data direction byte bits [7:1] of this byte represent the device slave address and bit [0] indicates the data transfer direction. a ?0? in bit [0] indicates a write, and a ?1? indicates a read. the default slave addresses used by the ar0833 for the mipi configured sensor are 0x6c (write address) and 0x6d (read address) in accordance with the mipi specification. alternate slave addresses of 0x6e(write address) and 0x6f(read address) can be selected by enabling and asserting the s addr signal through the gpi pad. the alternate slave addresses can also be programmed through r0x31fc. message byte message bytes are used for sending register addresses and register write data to the slave device and for retrieving register read data. acknowledge bit each 8-bit data transfer is followed by an acknowledge bit or a no-acknowledge bit in the s clk clock period following the data transfer. the transmitter (which is the master when writing, or the slave when reading) releases s data . the receiver indicates an acknowledge bit by driving s data low. no-acknowledge bit the no-acknowledge bit is generated when the receiver does not drive s data low during the s clk clock period following a data transfer. a no-acknowledge bit is used to terminate a read sequence. typical sequence a typical read or write sequence begins by the master generating a start condition on the bus. after the start condition, the master sends the 8-bit slave address/data direction byte. the last bit indicates whether the request is for a read or a write, where a ?0? indicates a write and a ?1? indicates a read. if the address matches the address of the slave device, the slave device acknowledges receipt of the address by generating an acknowledge bit on the bus. if the request was a write, the master then transfers the 16-bit register address to which the write should take place. this transfer takes place as two 8-bit sequences and the slave sends an acknowledge bit after each sequence to indicate that the byte has been received. the master then transfers the data as an 8-bit sequence; the slave sends an acknowledge bit at the end of the sequence. the master stops writing by generating a (re)start or stop condition. if the request was a read, the master sends the 8-bit write slave address/data direction byte and 16-bit register address, the same way as with a write request. the master then generates a (re)start condition and the 8-bit read slave address/data direction byte, and clocks out the register data, eight bits at a time. the master generates an acknowledge bit after each 8-bit transfer. the slave?s internal register address is automatically incremented after every 8 bits are transferred. the data transfer is stopped when the master sends a no-acknowledge bit.
ar0833 www. onsemi.com 12 single read from random location this sequence (figure 9) starts with a dummy write to the 16-bit address that is to be used for the read. the master terminates the write by generating a restart condition. the master then sends the 8-bit read slave address/data direction byte and clocks out one byte of register data. the master terminates the read by generating a no-acknowledge bit followed by a stop condition. figure 9 shows how the internal register address maintained by the ar0833 is loaded and incremented as the sequence proceeds. figure 9. single read from random location previous reg address, n reg address, m m+1 s0 1 p a sr slave address reg address[15:8] reg address[7:0] slave address s = start condition p = stop condition sr = restart condition a = acknowledge a = no-acknowledge slave to master master to slave a a a a read data single read from current location this sequence (figure 10) performs a read using the current value of the ar0833 internal register address. the master terminates the read by generating a no-acknowledge bit followed by a stop condition. the figure shows two independent read sequences. figure 10. single read from current location previous reg address, n reg address, n+1 n+2 s1 p slave address a read data s1 p slave address aa read data a sequential read, start from random location this sequence (figure 11) starts in the same way as the single read from random location (figure 9). instead of generating a no-acknowledge bit after the first byte of data has been transferred, the master generates an acknowledge bit and continues to perform byte reads until ?l? bytes have been read. figure 11. sequential read, start from random location previous reg address, n reg address, m s0 slave address a a reg address[15:8] p a m+1 a a a 1 sr reg address[7:0] read data slave address m+l m+l ? 1 m+l ? 2 m+1 m+2 m+3 a read data a read data a read data read data
ar0833 www. onsemi.com 13 sequential read, start from current location this sequence (figure 12) starts in the same way as the single read from current location (figure 10). instead of generating a no-acknowledge bit after the first byte of data has been transferred, the master generates an acknowledge bit and continues to perform byte reads until ?l? bytes have been read. figure 12. sequential read, start from current location n+l n+l ? 1 n+2 n+1 previous reg address, n p a s 1 read data a slave address read data read data read data aaa single write to random location this sequence (figure 13) begins with the master generating a start condition. the slave address/data direction byte signals a write and is followed by the high then low bytes of the register address that is to be written. the master follows this with the byte of write data. the write is terminated by the master generating a stop condition. figure 13. single write to random location previous reg address, n reg address, m m+1 s0 p slave address reg address[15:8] reg address[7:0] a a a a a write data sequential write, start at random location this sequence (figure 14) starts in the same way as the single write to random location (figure 13). instead of generating a no-acknowledge bit after the first byte of data has been transferred, the master generates an acknowledge bit and continues to perform byte writes until ?l? bytes have been written. the write is terminated by the master generating a stop condition. figure 14. sequential write, start at random location previous reg address, n reg address, m m+1 s0 slave address a reg address[15:8] a a a reg address[7:0] write data m+l m+l ? 1 m+l ? 2 m+1 m+2 m+3 write data a a a ap a write data write data write data
ar0833 www. onsemi.com 14 registers the ar0833 provides a 16-bit register address space accessed through a serial interface (?two-wire serial register interfac e?). each register location is 8 or 16 bits in size. the address space is divided into the five major regions shown in table 9. the remainder of this section describes these registers in detail. table 9. address space regions address range description 0x0000?0x0fff configuration registers (read-only and read-write dynamic registers) 0x1000?0x1fff parameter limit registers (read-only static registers) 0x2000?0x2fff image statistics registers (none currently defined) 0x3000?0x3fff manufacturer-specific registers (read-only and read-write dynamic registers) register notation the underlying mechanism for reading and writing registers provides byte write capability. however, it is convenient to consider some registers as multiple adjacent bytes. the ar0833 uses 8-bit, 16-bit, and 32-bit registers, all implemented as 1 or more bytes at naturally aligned, contiguous locations in the address space. in this document, registers are described either by address or by name. when registers are described by address, the size of the registers is explicit. for example, r0x3024 is a 2-bit register at address 0x3024, and r0x3000 ? 1 is a 16-bit register at address 0x3000?0x3001. when registers are described by name, the size of the register is implicit. it is necessary to refer to the register table to determine that model_id is a 16-bit register. register aliases a consequence of the internal architecture of the ar0833 is that some registers are decoded at multiple addresses. some registers in ?configuration space? are also decoded in ?manufacturer-specific space.? to provide unique names for all registers, the name of the register within manufacturer-specific register space has a trailing underscore. for example, r0x0202 is coarse_integration_time and r0x3012 is coarse_integration_time_. the effect of reading or writing a register through any of its aliases is identical. bit fields some registers provide control of several different pieces of related functionality, and this makes it necessary to refer to bit fields within registers. as an example of the notation used for this, the least significant 4 bits of the chip_version_reg register are referred to as chip_version_reg[3:0] or r0x0000 ? 1[3:0]. bit field aliases in addition to the register aliases described above, some register fields are aliased in multiple places. for example, r0x0100 (mode_select) has only one operational bit, r0x0100[0]. this bit is aliased to r0x301a?b[2]. the effect of reading or writing a bit field through any of its aliases is identical. byte ordering registers that occupy more than one byte of address space are shown with the lowest address in the highest ? order byte lane to match the byte-ordering on the data bus. for example, the chip_version_reg register is r0x0000 ? 1. in the register table the default value is shown as 0x4b00. this means that a read from address 0x0000 would return 0x4b, and a read from address 0x0001 would return 0x00. when reading this register as two 8-bit transfers on the serial interface, the 0x4b will appear on the serial interface first, followed by the 0x00. address alignment all register addresses are aligned naturally. registers that occupy 2 bytes of address space are aligned to even 16-bit addresses, and registers that occupy 4 bytes of address space are aligned to 16-bit addresses that are an integer multiple of 4. bit representation for clarity, 32-bit hex numbers are shown with an underscore between the upper and lower 16 bits. for example: 0x3000_01ab. data format most registers represent an unsigned binary value or set of bit fields. for all other register formats, the format is stated explicitly at the start of the register description. the notation for these formats is shown in table 10.
ar0833 www. onsemi.com 15 table 10. data formats name description fix16 signed fixed-point, 16-bit number: two?s complement number, 8 fractional bits. examples: 0x0100 = 1.0 0x8000 = ?128 0xffff = ?0.0039065 ufix16 unsigned fixed-point, 16-bit number: 8.8 format. examples: 0x0100 = 1.0 0x280 = 2.5 flp32 signed floating-point, 32-bit number: ieee 754 format. example: 0x4280_0000 = 64.0 register behavior registers vary from ?read-only,? ?read/write,? and ?read, write-1-to-clear.? double-buffered registers some sensor settings cannot be changed during frame readout. for example, changing r0x3004?5 (x_addr_start) partway through frame readout would result in inconsistent row lengths within a frame. to avoid this, the ar0833 double-buffers many registers by implementing a ?pending? and a ?live? version. reads and writes access the pending register. the live register controls the sensor operation. the value in the pending register is transferred to a live register at a fixed point in the frame timing, called frame start. frame start is defined as the point at which the first dark row is read out internally to the sensor. in the register tables the ?frame sync?d? column shows which registers or register fields are double-buffered in this way. using grouped_parameter_hold register grouped_parameter_hold (r0x301a[15]) can be used to inhibit transfers from the pending to the live registers. when the ar0833 is in streaming mode, this register should be written to ?1? before making changes to any group of registers where a set of changes is required to take effect simultaneously. when this register is written to ?0,? all transfers from pending to live registers take place on the next frame start. an example of the consequences of failing to set this bit follows: ? an external auto exposure algorithm might want to change both gain and integration time between two frames. if the next frame starts between these operations, it will have the new gain, but not the new integration time, which would return a frame with the wrong brightness that might lead to a feedback loop with the ae algorithm resulting in flickering. bad frames a bad frame is a frame where all rows do not have the same integration time or where offsets to the pixel values have changed during the frame. many changes to the sensor register settings can cause a bad frame. for example, when line_length_pck (r0x300c) is changed, the new register value does not affect sensor behavior until the next frame start. however, the frame that would be read out at that frame start will have been integrated using the old row width, so reading it out using the new row width would result in a frame with an incorrect integration time. by default, bad frames are masked. if the masked bad frame option is enabled, both lv and fv are inhibited for these frames so that the vertical blanking time between frames is extended by the frame time. in the register tables, the ?bad frame? column shows where changing a register or register field will cause a bad frame. this notation is used: ? n ? no. changing the register value will not produce a bad frame. ? y ? yes. changing the register value might produce a bad frame. ? ym ? yes; but the bad frame will be masked out when mask_corrupted_frames (r0x301a[9]) is set to ?1.? changes to integration time if the integration time is changed while fv is asserted for frame n , the first frame output using the new integration time is frame (n + 2) . the sequence is as follows: 1. during frame n , the new integration time is held in the pending register. 2. at the start of frame ( n + 1 ), the new integration time is transferred to the live register. integration for each row of frame ( n + 1 ) has been completed using the old integration time. 3. the earliest time that a row can start integrating using the new integration time is immediately after that row has been read for frame ( n + 1 ). the actual time that rows start integrating using the new integration time is dependent upon the new value of the integration time. 4. when frame ( n + 2 ) is read out, it will have been integrated using the new integration time. if the integration time is changed on successive frames, each value written will be applied for a single frame; the latency between writing a value and it affecting the frame readout remains at two frames.
ar0833 www. onsemi.com 16 changes to gain settings usually, when the gain settings are changed, the gain is updated on the next frame start. when the integration time and the gain are changed at the same time, the gain update is held off by one frame so that the first frame output with the new integration time also has the new gain applied. in this case, a new gain should not be set during the extra frame delay. there is an option to turn off the extra frame delay by setting extra_delay (r0x3018). clocking default setup gives a physical 73.2 mhz internal clock for an external input clock of 24 mhz. the sensor contains a phase-locked loop (pll) for timing generation and control. the pll contains a prescaler to divide the input clock applied on extclk, a vco to multiply the prescaler output, and a set of dividers to generate the output clocks. the pll structure is shown in figure 15. figure 15. clocking configuration pll _multiplier (r0x306) pll multiplier (m) pll internal vco frequency op_sys_clk op sys clk divider op pix clk divider op_pix_clk clk _ op divider clk_op row_speed (r0x3016[10:8]) op_pix_clk_div (r0x308) op_sys_clk_div (r0x30a) extclk pre pll divider (n +1) external input clock pll input clock pll_ip_clk_freq (4 ? 24 mhz) pre_pll_clk_div (r0x304) clk _ pixel divider vt_pix_clk row_speed (r0 x3016[2:0]) vt_sys_clk vt sys clk vt pix clk divider clk_pixel vt_pix_clk_div (r0x300) vt_sys_clk_div (r0x302) ext_clk_freq_mhz divider pll figure 15 shows the different clocks and the names of the registers that contain or are used to control their values. the vt_pix_clk is divided by two to compensate for the fact that the design has 2 digital data paths. this divider should always remain turned on. ar0833 has 10-to-8 and 10-to-6 compression. the framer ip packs two 6-bit pixels into one 12-bit data and sends it to physical layer. the framer takes the action to divide word clock into half speed. the word clock should be divided by 6 from vco at pll in order to match physical layer considering one data having 12 bit-clocks. the usage of the output clocks is shown below: ? clk_pixel (vt_pix_clk / row_speed[2:0]) is used by the sensor core to readout and control the timing of the pixel array. the sensor core produces one 10-bit pixel each vt_pix_clk period. the line length (line_length_pck) is controlled in increments of the clk_pixel period. ? clk_op (op_pix_clk / row_speed[10:8]) is used to load parallel pixel data from the output fifo (see figure 40) to the serializer. the output fifo generates one pixel each op_pix_clk period. ? op_sys_clk is used to generate the serial data stream on the output. the relationship between this clock frequency and the op_pix_clk frequency is dependent upon the output data format. the pixel frequency can be calculated in general as: pixel_clock_mhz ext_clk_freq_mhz pll_multiplier pre_pll_clk_div vt_sys_clk_div 2 vt_pix_clk_div row_speed[2:0] (eq. 1) the output clock frequency can be calculated as: clk_op_freq_mhz ext_clk_freq_mhz pll_multiplier pre_pll_clk_div op_sys_clk_div op_pix_clk_div row_speed[10:8] (eq. 2)
ar0833 www. onsemi.com 17 op_sys_clk_freq_mhz ext_clk_freq_mhz pll_multiplier pre_pll_clk_div op_sys_clk_div (eq. 3) pll clocking the pll divisors should be programmed while the ar0833 is in the software standby state. after programming the divisors, it is necessary to wait for the vco lock time before enabling the pll. the pll is enabled by entering the streaming state. an external timer will need to delay the entrance of the streaming mode by 1 millisecond so that the pll can lock. the effect of programming the pll divisors while the ar0833 is in the streaming state is undefined. clock control the ar0833 uses an aggressive clock-gating methodology to reduce power consumption. the clocked logic is divided into a number of separate domains, each of which is only clocked when required. when the ar0833 enters a soft standby state, almost all of the internal clocks are stopped. the only exception is that a small amount of logic is clocked so that the two-wire serial interface continues to respond to read and write requests. features interlaced hdr readout the sensor enables hdr by outputting frames where even and odd row pairs within a single frame are captured at different integration times. this output is then matched with an algorithm designed to reconstruct this output into an hdr still image or video. the sensor hdr is controlled by two shutter pointers (shutter pointer1, shutter pointer2) that control the integration of the odd (shutter pointer1) and even (shutter pointer 2) row pairs. figure 16. hdr integration time tint 1 tint 2 i ? frame 1 i ? frame 2 output frame from sensor exposure i ? frame 1 exposure i ? frame 1 shutter pointer 1 shutter pointer 2 sample pointer output i ? frame 1 and 2
ar0833 www. onsemi.com 18 integration time for interlaced hdr readout tint1 (integration time 1) and tint2 (integration time 2) the limits for the coarse integration time are defined by: coarse_integration_time_min coarse_integration_time (frame_length_lines coarse_integration_ti me_max_margin) (eq. 4) coarse_integration_time2_min coarse_integration_time2 (frame_length_lines coarse_integration_time2_max_margin) (eq. 5) the actual integration time is given by: integration_time coarse_integration_time line_length_pck vt_pix_clk_freq_mhz 10 6 (eq. 6) integration_time2 coarse_integration_time2 line_length_pck vt_pix_clk_freq_mhz 10 6 (eq. 7) if this limit is broken, the frame time will automatically be extended to (coarse_integration_time + coarse_ integration_time_max_margin) to accommodate the larger integration time. the ratio between even and odd rows is typically adjusted to 1 , 2 , 4 , and 8 . bayer resampler the imaging artifacts found from a 2 2 binning or summing will show image artifacts from aliasing. these can be corrected by resampling the sampled pixels in order to filter these artifacts. figure 17 shows the pixel location resulting from 2 2 summing or binning located in the middle and the resulting pixel locations after the bayer re-sampling function has been applied. figure 17. bayer resampling the improvements from using the bayer resampling feature can be seen in figure 18. in this example, image edges seen on a diagonal have smoother edges when the bayer re-sampling feature is applied. this feature is only designed to be used with modes configured with 2 2 binning or summing. the feature will not remove aliasing artifacts that are caused skipping pixels. figure 18. results of resampling 2 2 binned ? before 2 2 binned ? after resampling
ar0833 www. onsemi.com 19 to enable the bayer resampling feature: 1. set r0x400 = 2 // enable the on-chip scalar. 2. set r0x306e to 0x90b0 // configure the on-chip scalar to resample bayer data. to disable the bayer resampling feature: 1. set r0x400 = 0 // disable the on-chip scalar. 2. set r0x306e to 0x9080 // configure the on-chip scalar to resample bayer data. note: the image readout (rows and columns) has to have two extra rows and two extra columns when using the resample feature. figure 19. illustration of resampling operation image array readout 3264 2448 image size output 1632 1224 resampled image output 1632 1224 resampling 2 2 binning one-time programmable memory (otpm) the ar0833 features 5.6 kb of one-time programmable memory (otpm) for storing shading correction coefficients, individual module, and customer-specific information. the user may program the data before shipping. otpm can be accessed through two-wire serial interface. the ar0833 uses the auto mode for fast otpm programming and read operations. to read out the otpm, 1.8 v supply is required. as a result, a dedicated dv dd _1v8 pad has been implemented.during the programming process, a dedicated pin for high voltage needs to be provided to perform the anti-fusing operation. this voltage (v pp ) would need to be 6.5 v. the completion of the programming process will be communicated by a register through the two-wire serial interface. if the v pp pin does not need to be bonded out as a pin on the module, it should be left floating inside the module. the programming of the otpm requires the sensor to be fully powered and remain in software standby with its clock input applied. the information will be programmed through the use of the two-wire serial interface, and once the data is written to an internal register, the programming host machine will apply a high voltage to the programming pin, and send a program command to initiate the anti-fusing process. after the sensor has finished programming the otpm, a status bit will be set to indicate the end of the programming cycle, and the host machine can poll the setting of the status bit through the two-wire serial interface. only one programming cycle for the 16-bit word can be performed. reading the otpm data requires the sensor to be fully powered and operational with its clock input applied. the data can be read through a register from the two-wire serial interface. programming and verifying the otpm the procedure for programming and verifying the ar0833 otpm follows: 1. apply power to all the power rails of the sensor (v dd _io, v aa , v aa _pix, dv dd _1v2, dv dd _1v2_phy, and dv dd _1v8). v aa must be set to 2.8 v during the programming process. v pp must be initially floating. all other supplies must be at their nominal voltage. 2. provide a 12-mhz extclk clock input. 3. set r0x301a = 0x18, to put sensor in the soft standby mode. 4. set r0x3130 = 0xff01 (timing configuration) 5. set r0x304c[15:8] = record type (e.g. 0x30) 6. set r0x304c[7:0] = length of the record which is the number of otpm data registers that are filled in. 7. set r0x3054[9] = 0 to ensure that the error checking and correction is enabled. 8. write data into all the otpm data registers: r0x3800-r0x39fe. 9. ramp up vpp to 6.5 v. 10. set the otpm_control_auto_wr_start bit in the otpm_control register r0x304a[0] = 1, to initiate the auto program sequence. the sensor will now program the data into the otpm. 11. poll otpm_control_auto_wr_end (r0x304a [1]) to determine when the sensor is finished programming the word. 12. verify that the otpm_control_auto_wr_ success(0x304a[2]) bit is set. 13. if the above bits are not set to 1, then examine otpm_status register r0x304e[9] to verify if the otpm memory is full and 0x304e[10] to verify if otpm memory is insufficient. 14. remove the high voltage (v pp ) and float v pp pin. reading the otpm 1. apply power to all the power rails of the sensor (v dd _io, v aa , v aa _pix, dv dd _1v2, dv dd _1v2_phy, and dv dd _1v8) at their nominal voltage. 2. set extclk to normal operating frequency. 3. perform proper reset sequence to the sensor. 4. set r0x3134 = 0xcd95 (timing configuration)
ar0833 www. onsemi.com 20 5. set r0x304c[15:8] = record type (for example, 0x30) 6. set r0x304c[7:0] = length of the record which is the number of data registers to be read back. this could be set to 0 during otpm auto read if length is unknown. 7. set r0x3054 = 0x0400 8. initiate the auto read sequence by setting the otpm_control_auto_read_start bit (r0x304a[4]) = 1. 9. poll the otpm_control_auto_rd_end bit (r0x304a[5]) to determine when the sensor is finished reading the word(s). when this bit becomes 1, the otpm_control_auto_rd_success bit (r0x304a[6]) will indicate whether the memory was read successfully or not. 10. data can now be read back from the otpm_data registers (r0x3800-r0x39fe). image acquisition modes the ar0833 supports two image acquisition modes: 1. electronic rolling shutter (ers) mode. this is the normal mode of operation. when the ar0833 is streaming, it generates frames at a fixed rate, and each frame is integrated (exposed) using the ers. when the ers is in use, timing and control logic within the sensor sequences through the rows of the array, resetting and then reading each row in turn. in the time interval between resetting a row and subsequently reading that row, the pixels in the row integrate incident light. the integration (exposure) time is controlled by varying the time between row reset and row readout. for each row in a frame, the time between row reset and row readout is fixed, leading to a uniform integration time across the frame. when the integration time is changed (by using the two-wire serial interface to change register settings), the timing and control logic controls the transition from old to new integration time in such a way that the stream of output frames from the ar0833 switches cleanly from the old integration time to the new while only generating frames with uniform integration. see ?changes to integration time?. 2. global reset release (grr) mode. his mode can be used to acquire a single image at the current resolution. in this mode, the end point of the pixel integration time is controlled by an external electromechanical shutter, and the ar0833 provides control signals to interface to that shutter. the operation of this mode is described in detail in ?global reset release (grr)?. the benefit for the use of an external electromechanical shutter is that it eliminates the visual artifacts associated with ers operation. visual artifacts arise in ers operation, particularly at low frame rates, because an ers image effectively integrates each row of the pixel array at a different point in time. window control the sequencing of the pixel array is controlled by the x_addr_start, y_addr_start, x_addr_end, and y_addr_end registers. the output image size is controlled by the x_output_size and y_output_size registers. pixel border the default settings of the sensor provide a 3264 (h) x 2448 (v) image. a border of up to 8 pixels (4 in binning) on each edge can be enabled by reprogramming the x_addr_start, y_addr_start, x_addr_end, y_addr_end, x_output_size, and y_output_size registers accordingly. these border pixels can be used but are disabled by default. readout modes horizontal mirror the horizontal_mirror bit in the image_orientation register is set by default. the result of this is that the order of pixel readout within a row is reversed, so that readout starts from x_addr_end and ends at x_addr_start. figure 20 shows a sequence of 6 pixels being read out with horizontal_mirror = 0 and horizontal_mirror = 1. changing horizontal_mirror causes the bayer order of the output image to change; the new bayer order is reflected in the value of the pixel_order register. figure 20. effect of horizontal_mirror on readout order g0[9:0] r0[9:0] g1[9:0] r1[9:0] g2[9:0] r2[9:0] r2[9:0] g2[9:0] r1[9:0] g1[9:0] r0[9:0] g0[9:0] line_valid horizontal_mirror = 0 horizontal_mirror = 1 d out [9:0] d out [9:0]
ar0833 www. onsemi.com 21 vertical flip when the vertical_flip bit is set in the image_orientation register, the order in which pixel rows are read out is reversed, so that row readout starts from y_addr_end and ends at y_addr_start. figure 21 shows a sequence of 6 rows being read out with vertical_flip = 0 and vertical_flip = 1. changing vertical_flip causes the bayer order of the output image to change; the new bayer order is reflected in the value of the pixel_order register. figure 21. effect of vertical_flip on readout order row0[9:0] row1[9:0] row2[9:0] row3[9:0] row4[9:0] row5[9:0] row5[9:0] row4[9:0] row3[9:0] row2[9:0] row0[9:0] frame_valid vertical_flip = 0 vertical_flip = 1 row1[9:0] d out [9:0] d out [9:0] subsampling the ar0833 supports subsampling to reduce the amount of data processed by the signal chains in the ar0833, thereby allowing the frame rate to be increased and power consumption reduced. subsampling is enabled by setting x_odd_inc and/or y_odd_inc. values of 1, 3, and 7 can be supported. setting both of these variables to 3 reduces the amount of row and column data processed and is equivalent to the 2 2 skipping readout mode provided by the ar0833. setting x_odd_inc = 3 and y_odd_inc = 3 results in a quarter reduction in output image size. figure 22 shows a sequence of 8 columns being read out with x_odd_inc = 3 and y_odd_inc = 1. figure 22. effect of x_odd_inc = 3 on readout sequence g0[9:0] r0[9:0] g1[9:0] r1[9:0] g2[9:0] r2[9:0] g3[9:0] r3[9:0] g0[9:0] r0[9:0] g2[9:0] r2[9:0] line_valid x_odd_inc = 1 line_valid x_odd_inc = 3 d out [9:0] d out [9:0] a 1/16 reduction in resolution is achieved by setting both x_odd_inc and y_odd_inc to 7. this is equivalent to 4 4 skipping readout mode provided by the ar0833. figure 23 shows a sequence of 16 columns being read out with x_odd_inc = 7 and y_odd_inc = 1. figure 23. effect of x_odd_inc = 7 on readout sequence g0[9:0] r0[9:0] g1[9:0] r1[9:0] g2[9:0] g7[9:0] r7[9:0] g0[9:0] r0[9:0] g4[9:0] r4[9:0] line_valid x_odd_inc = 1 line_valid x_odd_inc = 7 ... d out [9:0] d out [9:0]
ar0833 www. onsemi.com 22 the effect of the different subsampling settings on the pixel array readout is shown in figure 24 through figure 26. figure 24. pixel readout (no subsampling) x incrementing y incrementing figure 25. skip2 pixel readout (x_odd_inc = 3, y_odd_inc = 3) x incrementing y incrementing figure 26. skip4 pixel readout (x_odd_inc = 7, y_odd_inc = 7) x incrementing y incrementing
ar0833 www. onsemi.com 23 programming restrictions when subsampling when subsampling is enabled and the sensor is switched back and forth between full resolution and subsampling, on semiconductor recommends that line_length_pck be kept constant between the two modes. this allows the same integration times to be used in each mode. when subsampling is enabled, it may be necessary to adjust the x_addr_start, x_addr_end, y_addr_start, and y_addr_end settings: the values for these registers are required to correspond with rows/columns that form part of the subsampling sequence. the adjustment should be made in accordance with these rules: x_skip_factor = (x_odd_inc + 1) / 2 y_skip_factor = (y_odd_inc + 1) / 2 ? x_addr_start should be a multiple of x_skip_factor x 4 ? (x_addr_end ? x_addr_start + x_odd_inc) should be a multiple of x_skip_factor x 4 ? (y_addr_end ? y_addr_start + y_odd_inc) should be a multiple of y_skip_factor x 4 the number of columns/rows read out with subsampling can be found from the equation below: ? columns/rows = (addr_end ? addr_start + odd_inc) / skip_factor table 11 shows the row or column address sequencing for normal and subsampled readout. in the 2x skip case, there are two possible subsampling sequences (because the subsampling sequence only reads half of the pixels) depending upon the alignment of the start address. similarly, there will be four possible subsampling sequences in the 4x skip case (though only the first two are shown in table 11). table 11. row address sequencing during subsampling odd_inc = 1 (normal) odd_inc = 3 (2 skip) odd_inc = 7 (4 skip) start = 0 start = 0 start = 0 0 0 0 1 1 1 2 3 4 4 5 5 6 7 8 8 8 9 9 9 10 11 12 12 13 13 14 15 binning the ar0833 supports 2 x 1 (column binning, also called x-binning). bi nning has many of the same characteristics as skipping, but because it gathers image data from all pixels in the active window (rather than a subset of them), it achieves superior image quality and avoids the aliasing artifacts that can be a characteristic side effect of skipping. binning is enabled by selecting the appropriate subsampling settings (in read_mode, the sub-register x_odd_inc = 3 and y_odd_inc = 1 for x-binning and setting the appropriate binning bit in read_mode r0x3040[11] = 1 for x_bin_enable). as with skipping, x_addr_end and y_addr_end may require adjustment when binning is enabled. it is the first of the two columns/rows binned together that should be the end column/row in binning, so the requirements to the end address are exactly the same as in skipping mode. the effect of the different binning is shown in figure 27 below and figure 28. binning can also be enabled when the 4x subsampling mode is enabled (x_odd_inc = 7 and y_odd_inc = 1 for x-binning, x_odd_inc = 7 and y_odd_inc = 7 for 4x xy-binning). in this mode, however, not all pixels will be used so this is not a 4x binning implementation. an implementation providing a combination of skip2 and bin2 is used to achieve 4x subsampling with better image quality. the effect of this subsampling mode is shown in figure 28.
ar0833 www. onsemi.com 24 figure 27. bin2 pixel readout (x_odd_inc = 3, y_odd_inc = 1, x_bin = 1) x incrementing y incrementing figure 28. bin2 pixel readout (x_odd_inc = 3, y_odd_inc = 3, x_bin = 1) x incrementing y incrementing
ar0833 www. onsemi.com 25 binning address sequencing is a bit more complicated than during subsampling only, because of the implementation of the binning itself. for a given column n , there is only one other column, n_bin, that can be binned with, because of physical limitations in the column readout circuitry. the possible address sequences are shown in table 12. table 12. column address sequencing during binning odd_inc = 1 (normal) odd_inc = 3 (2 bin) odd_inc = 7 (2 skip + 2 bin) x_addr_start = 0 x_addr_start = 0 x_addr_start = 0 0 0/2 0/4 1 1/3 1/5 2 3 4 4/6 5 5/7 6 7 8 8/10 8/12 9 9/11 9/13 10 11 12 12/14 13 13/15 14 15 there are no physical limitations on what can be binned together in the row direction. a given row n will always be binned with row n+2 in 2x subsampling mode and with row n+4 in 4x subsampling mode. therefore, which rows get binned together depends upon the alignment of y_addr_start. the possible sequences are shown in t able 13. table 13. row address sequencing during binning odd_inc = 1 (normal) odd_inc = 3 (2 bin) odd_inc = 7 (2 skip + 2 bin) y_addr_start = 0 y_addr_start = 0 y_addr_start = 0 0 0/2 0/4 1 1/3 1/5 2 3 4 4/6 5 5/7 6 7 8 8/10 8/12 9 9/11 9/13 10 11 12 12/14 13 13/15 14 15
ar0833 www. onsemi.com 26 programming restrictions when binning and summing binning and summing require different sequencing of the pixel array and impose different timing limits on the operation of the sensor. as a result, when xy-subsampling is enabled, some of the programming limits declared in the parameter limit registers are no longer valid. in addition, the default values for some of the manufacturer-specific registers need to be reprogrammed. see ?minimum frame time? and ?minimum row time?. subsampling/binning options: 1. xskipyskip r0x3040[11], x_bin_en: 0 r0x3040[13], row_sum: 0 r0x0382: x_odd_inc = 3 (xskip2) or 7 (xskip4) r0x0386: y_odd_inc = 3 (yskip2), 7 (yskip4) or 15 (yskip8) 2. xbinyskip r0x3040[11], x_bin_en: 1 r0x3040[13], row_sum: 0 r0x0382: x_odd_inc = 3 (xbin2) r0x0386: y_odd_inc = 3 (yskip2), 7 (yskip4) or 15 (yskip8) 3. xskipysum r0x3040[11], x_bin_en: 0 r0x3040[13], row_sum: 1 r0x0382: x_odd_inc = 3 (xskip2) or 7 (xskip4) r0x0386: y_odd_inc = 3 (ysum2) 4. xbinysum r0x3040[11], x_bin_en: 1 r0x3040[13], row_sum: 1 r0x0382: x_odd_inc = 3 (xbin2) r0x0386: y_odd_inc = 3 (ysum2) 5. xsumysum r0x3040[11], x_bin_en: 1 r0x3040[13], row_sum: 1 r0x3ee4[0], sreg_colamp_sum2: 1 (cannot write to this bit when streaming ? have to write to entire register) r0x0382: x_odd_inc = 3 (xsum2) r0x0386: y_odd_inc = 3 (ysum2) binning, skipping, and summing mode summing, skipping, and binning can be combined in the modes listed in table 14. unlike binning mode where the values of adjacent same color pixels are averaged together, summing adds the pixel values together resulting in better sensor sensitivity. summing is supposed to provide two times the sensitivity compared to the binning only mode. table 14. available skip, bin, and sum modes in the ar0833 sensor subsampling method horizontal vertical skipping 2 , 4 2 , 4 , 8 binning 2 summing 2 2 figure 29. pixel binning and summing 2 2 binning or summing x-binning summing avg avg h h v v
ar0833 www. onsemi.com 27 scaler scaling reduces the size of the output image while maintaining the same field ? of ? view. the input and output of the scaler is in bayer format. when compared to skipping, scaling is advantageous as it avoids aliasing. the scaling factor, programmable in 1/16 steps, is used for horizontal and vertical scalers. the ar0833 sensor is capable of horizontal scaling and full (horizontal and vertical) scaling. the scale factor is determined by: ? n , which is fixed at 16 ? m , which is adjustable with register r0x0404 ? legal values for m are 16 through 96, giving the user the ability to scale from 1:1 (m = 16) to 1:6 (m = 96) frame rate control the formulas for calculating the frame rate of the ar0833 are shown below. the line length is programmed directly in pixel clock periods through register line_length_pck. for a specific window size, the minimum line length can be found from equation 8: minimum line_length_pck x_addr_end x_addr_start 1 subsampling factor min_line_blanking_pck (eq. 8) note that line_length_pck also needs to meet the minimum line length requirement set in register min_line_length_pck. the row time can either be limited by the time it takes to sample and reset the pixel array for each row, or by the time it takes to sample and read out a row. values for min_line_blanking_pck are provided in ?minimum row time?. the frame length is programmed directly in number of lines in the register frame_line_length. for a specific window size, the minimum frame length can be found in equation 9: minimum frame_length_lines y_addr_end y_addr_start 1 subsampling factor min_frame_blanking_lines (eq. 9) the frame rate can be calculated from these variables and the pixel clock speed as shown in equation 10: frame rate vt_pixel_clock_mhz 1 10 6 line_length_pck frame_length_lines (eq. 10) if coarse_integration_time is set larger than frame_length_lines the frame size will be expanded to coarse_integration_time + 1. minimum row time enough time must be given to the output fifo so it can output all data at the set frequency within one row time. there are therefore two checks that must all be met when programming line_length_pck: ? line_length_pck min_line_length_pck in table 15 ? the row time must allow the fifo to output all data during each row. that is, line_length_pck (x_output_size 2 + 0x005e) ?vt_pix_clk period? / ?op_pix_clk period? minimum frame time the minimum number of rows in the image is 1, so min_frame_length_lines will always equal (min_frame _blanking_lines + 1). table 15. minimum frame time and blanking numbers min_frame_blanking_lines 0x008f min_frame_length_lines 0x0a1f integration time the integration (exposure) time of the ar0833 is controlled by the coarse_integration_time register. the limits for the coarse integration time are defined by: coarse_integration_time_min coarse_integration_time (eq. 11) the actual integration time is given by: integration_time coarse_integration_time line_length_pck vt_pix_clk_freq_mhz 10 6 (eq. 12) it is required that: coarse_integration_time (frame_length_lines coarse_integration_time_max_margin) (eq. 13) if this limit is broken, the frame time will automatically be extended to (coarse_integration_time + coarse_integartion_ time_max_margin) to accommodate the larger integration time. in binning mode, frame_length_lines should be set larger than coarse_integration_time by at least 3 to avoid column imbalance artifact.
ar0833 www. onsemi.com 28 flash timing control the ar0833 supports both xenon and led flash timing through the flash output signal. the timing of the flash signal with the default settings is shown in figure 30 (xenon) and figure 31 (led). the flash and flash_count registers allow the timing of the flash to be changed. the flash can be programmed to fire only once, delayed by a few frames when asserted, and (for xenon flash) the flash duration can be programmed. enabling the led flash will cause one bad frame, where several of the rows only have the flash on for part of their integration time. this can be avoided either by first enabling mask bad frames (r0x301a[9] = 1) before the enabling the flash or by forcing a restart (r0x301a[1] = 1) immediately after enabling the flash; the first bad frame will then be masked out, as shown in figure 31. read-only bit flash[14] is set during frames that are correctly integrated; the state of this bit is shown in figures 30 and figure 31. figure 30. xenon flash enabled frame_valid flash strobe state of triggered bit (r0x3046 ? 7[14]) figure 31. led flash enabled note: an option to invert the flash output signal through r0x3046[7] is also available. frame_valid flash strobe state of triggered bit (r0x3046 ? 7[14]) flash enabled during this frame bad frame is masked good frame good frame bad frame is masked flash disabled during this frame global reset release (grr) global reset release mode allows the integration time of the ar0833 to be controlled by an external electromechanical shutter. grr mode is generally used in conjunction with ers mode. the ers mode is used to provide viewfinder information, the sensor is switched into grr mode to capture a single frame, and the sensor is then returned to ers mode to restore viewfinder operation. overview of global reset release sequence the basic elements of the grr sequence are: 1. by default, the sensor operates in ers mode and the shutter output signal is low. the electromechanical shutter must be open to allow light to fall on the pixel array. integration time is controlled by the coarse_integration_time register. 2. a global reset sequence is triggered. 3. all of the rows of the pixel array are placed in reset. 4. all of the rows of the pixel array are taken out of reset simultaneously. all rows start to integrate incident light. the electromechanical shutter may be open or closed at this time. 5. if the electromechanical shutter has been closed, it is opened. 6. after the desired integration time (controlled internally or externally to the ar0833), the electromechanical shutter is closed. 7. a single output frame is generated by the sensor with the usual lv, fv, pixclk, and d out timing. as soon as the output frame has completed (fv negates), the electromechanical shutter may be opened again. 8. the sensor automatically resumes operation in ers mode. this sequence is shown in figure 32. the following sections expand to show how the timing of this sequence is controlled.
ar0833 www. onsemi.com 29 figure 32. overview of global reset sequence ers row reset integration readout ers entering and leaving the global reset sequence a global reset sequence can be triggered by a register write to r0x315e global_seq_trigger[0] (global trigger, to transition this bit from a 0 to a 1) or by a rising edge on a suitably-configured gpi input). when a global reset sequence is triggered, the sensor waits for the end of the current row. when lv negates for that row, fv is negated 6 pixclk periods later, potentially truncating the frame that was in progress. the global reset sequence completes with a frame readout. at the end of this readout phase, the sensor automatically resumes operation in ers mode. the first frame integrated with ers will be generated after a delay of approximately ((13 + coarse_integration_time) x line_length_pck). this sequence is shown in figure 33. while operating in ers mode, double-buffered registers (?double-buffered registers?) are updated at the start of each frame in the usual way. during the global reset sequence, double-buf fered registers are updated just before the start of the readout phase. figure 33. entering and leaving a global reset sequence ers row reset integration readout ers trigger wait for end of current row automatic at end of frame readout programmable settings the registers global_rst_end and global_read_start allow the duration of the row reset phase and the integration phase to be controlled, as shown in figure 34. the duration of the readout phase is determined by the active image size. the recommended setting for global_rst_end is 0x3160 (for example, 512 s total reset time) with default vt_pix_clk. this allows sufficient time for all rows of the pixel array to be set to the correct reset voltage level. the row reset phase takes a finite amount of time due to the capacitance of the pixel array and the capability of the internal voltage booster circuit that is used to generate the reset voltage level. as soon as the global_rst_end count has expired, all rows in the pixel array are taken out of reset simultaneously and the pixel array begins to integrate incident light. figure 34. controlling the reset and integration phases of the global reset sequence ers row reset integration readout ers trigger wait for end of current row automatic at end of frame readout global_rst_end global_read_start control of the electromechanical shutter figure 35 shows two dif ferent ways in which a shutter can be controlled during the global reset sequence. in both cases, the maximum integration time is set by the difference between global_read_start and global_rst_end. in shutter example 1, the shutter is open during the initial ers sequence and during the row reset phase. the shutter closes during the integration phase. the pixel array is integrating incident light from the start of the integration phase to the point at which the shutter closes. finally, the shutter opens again after the end of the readout phase. in shutter example 2, the shutter is open during the initial ers sequence and closes sometime during the row reset phase. the shutter both opens and closes during the integration phase. the pixel array is integrating incident light for the part of the integration phase during which the shutter is open. as for the previous example, the shutter opens again after the end of the readout phase.
ar0833 www. onsemi.com 30 figure 35. control of the electromechanical shutter ers row reset integration readout ers trigger wait for end of current row automatic at end of frame readout global_rst_end global_read_start maximum integration time actual integration time closed shutter closed shutter open shutter open shutter closed shutter open actual integration time shutter example 1 shutter open (physical) shutter example 2 shutter open (physical) it is essential that the shutter remains closed during the entire row readout phase (that is, until fv has negated for the frame readout); otherwise, some rows of data will be corrupted (over-integrated). it is essential that the shutter closes before the end of the integration phase. if the row readout phase is allowed to start before the shutter closes, each row in turn will be integrated for one row-time longer than the previous row. after fv negates to signal the completion of the readout phase, there is a time delay of approximately (10 x line_length_pck) before the sensor starts to integrate light-sensitive rows for the next ers frame. it is essential that the shutter be opened at some point in this time window; otherwise, the first ers frame will not be uniformly integrated. the ar0833 provides a shutter output signal to control (or help the host system control) the electromechanical shutter. the timing of the shutter output is shown in figure 36. shutter is negated by default. the point at which it asserts is controlled by the programming of global_shutter_start. at the end of the global reset readout phase, shutter negates approximately (2 x line_length_pck) after the negation of fv. this programming restriction must be met for correct operation: ? global_read_start > global_shutter_start figure 36. controlling the shutter output ers row reset integration readout ers trigger wait for end of current row automatic at end of frame readout global_rst_end global_read_start shutter (signal) global_shutter_start ~2 line_length_pck
ar0833 www. onsemi.com 31 using flash with global reset if r0x315e global_seq_trigger[2] = 1 (global flash enabled) when a global reset sequence is triggered, the flash output signal will be pulsed during the integration phase of the global reset sequence. the flash output will assert a fixed number of cycles after the start of the integration phase and will remain asserted for a time that is controlled by the value of the flash_count register. when flash_count is programmed for value n, (where n is 0?0x3fe) the resulting flash duration is given by n x 512 x (1/vt_pix_clk_freq_mhz), as shown in figure 37. figure 37. using flash with global reset ers row reset integration readout ers trigger wait for end of current row automatic at end of frame readout global_rst_end global_read_start shutter global_shutter_start ~2 line_length_pck flash (fixed) flash_count when the flash_count = 0x3ff, the flash signal will be maximized and goes low when readout starts, as shown in figure 38. this would be preferred if the latency in closing the shutter is longer than the latency for turning off the flash. this guarantees that the flash stays on while the shutter is open. figure 38. extending flash duration in global reset (reference readout start) ers row reset integration readout ers trigger wait for end of current row automatic at end of frame readout global_rst_end global_read_start shutter global_shutter_start ~2 line_length_pck flash (fixed)
ar0833 www. onsemi.com 32 external control of integration time if global_seq_trigger[1] = 1 (global bulb enabled) when a global reset sequence is triggered, the end of the integration phase is controlled by the level of trigger (global_seq_trigger[0] or the associated gpi input). this allows the integration time to be controlled directly by an input to the sensor. this operation corresponds to the shutter ?b? setting on a traditional camera, where ?b? originally stood for ?bulb? (the shutter setting used for synchronization with a magnesium foil flash bulb) and was later considered to stand for ?brief? (an exposure that was longer than the shutter could automatically accommodate). when the trigger is de-asserted to end integration, the integration phase is extended by a further time given by global_read_start ? global_shutter_start . usually this means that global_read_start should be set to global_shutter_start + 1 . the operation of this mode is shown in figure 39. the figure shows the global reset sequence being triggered by the gpi2 input, but it could be triggered by any of the gpi inputs or by the setting and subsequence clearing of the global_seq_trigger[0] under software control. the integration time of the grr sequence is defined as: integration time global_scale [global_read_start global_shutter_start global_rst_end] vt_pix_clk_freq_mhz (eq. 14) where: global_read_start 2 16 global_read_start2[7:0] global_read_start1[15:0] (eq. 15) global_shutter_start 2 16 global_shutter_start2[7:0] global_shutter_start1[15:0] (eq. 16) the integration equation allows for 24-bit precision when calculating both the shutter and readout of the image. the global_rst_end has only 16-bit as the array reset function and requires a short amount of time. the integration time can also be scaled using global_scale. the variable can be set to 0?512, 1?2048, 2?128, and 3?32. these programming restrictions must be met for correct operation of bulb exposures: ? global_read_start > global_shutter_start ? global_shutter_start > global_rst_end ? global_shutter_start must be smaller than the exposure time (that is, this counter must expire before the trigger is de-asserted) figure 39. global reset bulb ers row reset integration readout ers trigger wait for end of current row automatic at end of frame readout global_rst_end gpi2 global_read_start ? global_shutter_start retriggering the global reset sequence the trigger for the global reset sequence is edge-sensitive; the global reset sequence cannot be retriggered until the global trigger bit (in the r0x315e global_seq_trigger register) has been returned to ?0,? and the gpi (if any) associated with the trigger function has been negated. the earliest time that the global reset sequence can be retriggered is the point at which the shutter output negates; this occurs approximately (2 x line_length_pck) after the negation of fv for the global reset readout phase. using global reset with smia data path when a global reset sequence is triggered, it usually results in the frame in progress being truncated (at the end of the current output line). the smia data path limiter function (see figure 40) attempts to extend (pad) all frames to the programmed value of y_output_size. if this padding is still in progress when the global reset readout phase starts, the smia data path will not detect the start of the frame correctly. therefore, to use global reset with the serial data path, this timing scenario must be avoided. one possible way of doing this would be to synchronize (under software control) the assertion of trigger to an end-of-frame marker on the serial data stream. at the end of the readout phase of the global reset sequence, the sensor automatically resumes operation in ers mode.
ar0833 www. onsemi.com 33 global reset and soft standby if the r0x301a[2] mode_select[stream] bit is cleared while a global reset sequence is in progress, the ar0833 will remain in streaming state until the global reset sequence (including frame readout) has completed, as shown in figure 40. figure 40. entering soft standby during a global reset sequence ers row reset integration readout ers software standby streaming system style r0x0100 mode_select[streaming] slave mode slave mode is to ensure having an ers-grr-ers transition without a broken ers frame before grr. it requests to trigger/end the grr sequence through the pin which is similar to the grr bulb mode. the major difference to our existing sensor is to start the grr sequence after the end of the current frame instead of to start immediately in the next following row. figure 41. slave mode transition sensor readout sensor readout sensor readout grr trig on wait for vd, then global reset sequence starts sensor starts to read out after vd is inserted vd
ar0833 www. onsemi.com 34 gain ar0833 supports both analog and digital gain. analog gain analog gain is provided by colamp and adc reference scaling (there is no asc gain due to column parallel nature of architecture). only global (not per -color) coarse gain can be set by analog gain. global gain register (r0x305e) sets the analog gain. bits [1:0] set the colamp gain while bits [4:2] are reserved for adc gain. while the 2-bit colamp gain provides up to 4x analog gain, only lsb (bit [2]) of adc gain bits is utilized to support 2x adc gain. table 16 is the recommended gain setting: table 16. recommended analog gain setting colamp gain codes (r0x305e[1:0]) adc gain codes (r0x305e[4:2]) colamp gain adc gain total gain 0 0 0 0 0 1 1 1 0 1 0 0 0 2 1 2 1 0 0 0 0 3 1 3 1 1 0 0 0 4 1 4 1 0 0 0 1 3 2 6 1 1 0 0 1 4 2 8 digital gain digital gain provides both per-color and fine (sub 1x) gain. the analog and digital gains are multiplicative to give the total gain. digital gain is set by setting bits r0x305e[15:5] to set global gain or by individually setting digital color gain r0x3056-c[15:5] where these 11 bits are designed in 4p7 format i.e. 4 msb provide gain up to 15x in step of 1x while 7 lsb provide sub-1x gain with a step size of 1/128. this sub-1x gain provides the fine gain control for the sensor. total gain max. total gain required by design spec is 8x (analog) and 16x (digital) with min. step size of 1/8. the total gain equation can be formulated as: total gain (1 dec(r0x305d[1:0])) (1 r0x305e[2]) dec(r0x305x[15:5]) 128 (eq. 17) where x is 6, 8, a, c, for gr, b, r and gb, respectively. note: on semiconductor recommends using the registers mentioned above for gain settings. avoid r0x3028 to r0x3038 unless their mapping to above registers is well understood and taken into account.
ar0833 www. onsemi.com 35 temperature sensor a standalone ptat based temperature sensor has been implemented. the block is controlled independent of sensor timing and all communication happens through the two-wire serial interface. internal vcm driver the ar0833 utilizes an internal voice coil motor (vcm) driver. the vcm functions are register-controlled through the serial interface. there are two output ports, vcm_isink and vcm_gnd, which would connect directly to the af actuator. take precautions in the design of the power supply routing to provide a low impedance path for the ground connection. appropriate filtering would also be required on the actuator supply. typical values would be a 0.1 f and 10 f in parallel. figure 42. vcm driver typical diagram ar0833 vcm v vcm d gnd 10 f vcm_isink vcm_gnd table 17. vcm driver typical characteristic parameter minimum typical maximum unit vcm_out voltage at vcm current sink 2.5 2.8 3.3 v wvcm voltage at vcm actuator 2.5 2.8 3.3 v inl relative accuracy ? 1.5 4 lsb res resolution ? 8 ? bits dnl differential nonlinearity ? 1 ? +1 lsb ivcm output current 90 100 110 ma slew rate (user programmable) ? ? 13 ma/ms
ar0833 www. onsemi.com 36 spectral characteristics figure 43. quantum efficiency wavelength (nm) quantum efficiency (%) 70 60 50 40 30 20 10 0 350 400 450 500 550 600 650 700 750 red green blue cra vs. image height plot image height cra (%) (mm) (deg) figure 44. chief ray angle (cra) vs. image height 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 0 102030405060708090100110 cra (deg) image height (%) 0 0 0 5 0.143 2.58 10 0.286 5.12 15 0.428 7.61 20 0.571 10.07 25 0.714 12.47 30 0.857 14.80 35 1.000 17.05 40 1.142 19.18 45 1.285 21.17 50 1.428 23.00 55 1.571 24.64 60 1.714 26.07 65 1.856 27.26 70 1.999 28.21 75 2.142 28.91 80 2.285 10.59 85 2.428 10.93 90 2.570 11.18 95 2.713 11.34 100 2.856 11.40
ar0833 www. onsemi.com 37 electrical characteristics two-wire serial register interface the electrical characteristics of the two-wire serial register interface (s clk , s data ) are shown in figure 45 and table 18. table 19 shows the timing specification for the two-wire serial interface. ?? ?? ?? ?? ?? figure 45. two-wire serial bus timing parameters note: read sequence: for an 8-bit read, read waveforms start after write command and register address are issued. 70% 30% 70% 30% 30% 30% 70% 70% 70% 30% 30% s 1 st clock 9 th clock s data s clk t srth t r t f t sds t sdh t acv t sdv s data s clk 9 th clock 70% 70% 70% 70% 30% 70% 70% 70% 30% t high t srts sr t low 30% t stps s p t buf table 18. two-wire serial register interface electrical characteristics (f extclk = 25 mhz; v aa = 2.8 v; v aa _pix = 2.8 v; v dd _io = 1.8 v; v dd (digital core) = 1.2 v; v dd _pll = 1.2 v; v dd _tx = 1.8 v; output load = 68.5 pf; t j = 55 c) symbol parameter condition min typ max unit v il input low voltage ? 0.5 ? 0.3 v dd _io v v ih input high voltage 0.7 v dd _ io ? v dd _ io + 0.5 v i in input leakage current no pull up resistor; v in = v dd _io or d gnd 10 ? 14 a v ol output low voltage at specified 2 ma 0.11 ? 0.3 v i ol output low current at specified v ol 0.1 v ? ? 6 ma c in input pad capacitance ? ? 6 pf c load load capacitance ? ? n/a pf table 19. two-wire serial interface timing specifications (v dd = 1.7 ? 1.9 v; v aa = 2.4 ? 3.1 v; environment temperature = ? 30 c to 50 c) symbol definition min max unit f sclk s clk frequency 100 400 khz t high s clk high period 0.6 ? s t low s clk low period 1.3 ? s t srts start setup time 0.6 ? s t srth start hold time 0.6 ? s t sds data setup time 100 ? ns t sdh data hold time 0 ? s t sdv data valid time ? 0.9 s t acv data valid acknowledge time ? 0.9 s t stps stop setup time 0.6 ? s t buf bus free time between stop and start 1.3 ? s
ar0833 www. onsemi.com 38 table 19. two-wire serial interface timing specifications (continued) (v dd = 1.7 ? 1.9 v; v aa = 2.4 ? 3.1 v; environment temperature = ? 30 c to 50 c) symbol unit max min definition t r s clk and s data rise time ? 300 ns t f s clk and s data fall time ? 300 ns extclk the electrical characteristics of the extclk input are shown in table 20. the extclk input supports an ac-coupled sine-wave input clock or a dc-coupled square-wave input clock. if extclk is ac-coupled to the ar0833 and the clock is stopped, the extclk input to the ar0833 must be driven to ground or to v dd_ io. failure to do this will result in excessive current consumption within the extclk input receiver. table 20. electrical characteristics (extclk) (f extclk = 24 mhz; v aa = 2.8 v; v aa _pix = 2.8 v; v dd _io = 1.8 v; dv dd _1v2 = 1.2 v, output load = 68.5 pf; t j = 55 c) symbol parameter condition min typ max unit f extclk1 input clock frequency pll enabled 6 24 27 mhz t r input clock rise slew rate c load <20pf ? 2.883 ? ns t f input clock fall slew rate c load <20pf ? 2.687 ? ns v in_ac input clock minimum voltage swing (ac coupled) ? 0.5 ? ? v (p-p) v in_dc input clock maximum voltage swing (dc coupled) ? ? ? v dd _io + 0.5 v f clkmax(ac) input clock signaling frequency (low amplitude) v in = v in_ac (min) ? ? 25 mhz f clkmax(dc) input clock signaling frequency (full amplitude) v in = v dd _ io ? ? 48 mhz clock duty cycle ? 45 50 55 % t jitter input clock jitter cycle-to-cycle ? 545 600 ps t lock pll vco lock time ? ? 0.2 2 ms c in input pad capacitance ? ? 6 ? pf i ih input high leakage current ? 0 ? 10 a v ih input high voltage 0.7 v dd _io ? v dd _io + 0.5 ? v v il input low voltage ? 0.5 ? 0.3 v dd _io ? v product parametric performance is indicated in the electrical characteristics for the listed test conditions, unless otherwise noted. product performance may not be indicated by the electrical characteristics if operated under different conditions.
ar0833 www. onsemi.com 39 serial pixel data interface the electrical characteristics of the serial pixel data interface (clk_p, clk_n, data[4:1]_p, and data[4:1]_n) are shown in table 21. table 21. electrical characteristics (serial mipi pixel data interface) symbol parameter min typ max unit v od high speed transmit differential voltage 140 270 mv v cmtx high speed transmit static common-mode voltage 150 200 250 mv v od v od mismatch when output is differential-1 or differential-0 <10 mv z os single ended output impedance 40 50 62.5 z os single ended output impedance mismatch <14 % v cmtx(l,f) common-level variation between 50?450 mhz <25 mv t r rise time (20?80%) 150 350 380 ps t f fall time (20?80%) 150 350 380 ps v ol lp output low level ?50 to 50 mv v oh lp output high level 1.1 1.3 v z olp output impedance of low power parameter 140 t rlp 15?85% rise time 25 ns t flp 15?85% fall time 25 ns v/ dtsr slew rate (c load = 20?70 pf) 30 mv/ns control interface the electrical characteristics of the control interface (reset_bar, test, gpio0, gpio1, gpi2, and gpi3) are shown in table 22. table 22. dc electrical characteristics (control interface) (f extclk = 24 mhz; v aa = 2.8 v; v aa _pix = 2.8 v; v dd _io = 1.8 v; dv dd _1v2 = 1.2 v, output load = 68.5 pf; t j = 55 c) symbol parameter condition min typ max unit v ih input high voltage 0.7 x v dd_ io ? v dd_ io + 0.5 v v il input low voltage ?0.5 ? v dd_ io x 0.3 v i in input leakage current no pull-up resistor; v in = v dd_ io or d gnd ? ? 10 a c in input pad capacitance ? 6 ? pf operating voltages v aa and v aa _pix must be at the same potential for correct operation of the ar0833. table 23. maximum value ranges (f extclk = 24 mhz; v aa = 2.8 v; v aa _pix = 2.8 v; v dd _io = 1.8v; dv dd _1v2 = 1.2 v; output load = 68.5 pf; t j = 70 c; mode = full resolution (3264 x 2488); frame rate = 30 fps) symbol parameter condition min typ max unit v aa analog voltage 2.5 2.8 3.1 v v aa _pix pixel supply voltage 2.5 2.8 3.1 v dv dd _1v2 digital voltage 1.14 1.2 1.3 v dv dd _1v8 phy digital voltage 1.7 1.8 1.9 v v dd _io i/o digital voltage 1.7 1.8 1.9 v 2.5 2.8 3.1 v dv dd _1v2_phy mipi supply 1.14 1.2 1.3 v
ar0833 www. onsemi.com 40 table 23. maximum value ranges (continued) (f extclk = 24 mhz; v aa = 2.8 v; v aa _pix = 2.8 v; v dd _io = 1.8v; dv dd _1v2 = 1.2 v; output load = 68.5 pf; t j = 70 c; mode = full resolution (3264 x 2488); frame rate = 30 fps) symbol unit max typ min condition parameter h/w standby current consumption ? ? 30 a h/w standby power consumption ? ? 84 w output driving strength 10 ? ? ma slew rate ? 0.7 ? v/sec programming voltage for otpm (v pp ) 6 6.5 7 v t op operating temperature measure at junction ?30 ? 70 c t stg storage temperature ?40 ? 85 c typical operating current consumption (mipi) table 24. typical operating current consumption (mipi) (nominal voltages: f extclk = 24 mhz; v aa = 2.8 v; v aa _pix = 2.8 v; dv dd _1v8 = 1.8 v; v dd _io = 1.8 v; dvdd_1v2 = 1.2 v high voltages: f extclk = 24 mhz; v aa = 3.1 v; v aa _pix = 3.1 v; dv dd _1v8 = 1.9 v; v dd _io = 1.9 v; dv dd _1v2 = 1.3 v; t j = 25 c) symbol parameter condition min typ max unit i aa analog supply current full resolution 4:3 ? 30 fps ? 55 75 ma full resolution 16:9 ? 30 fps ? 55 75 ma 1080p, 30 fps ? 43 75 ma 720p, 60 fps ? 55 75 ma vga, 60 fps ? 55 75 ma i aa _pix pixel supply current full resolution 4:3 ? 30 fps ? 14 18 ma full resolution 16:9 ? 30 fps ? 14 18 ma 1080p, 30 fps ? 8 18 ma 720p, 60 fps ? 14 18 ma vga, 60 fps ? 14 18 ma i dd _1v8 otpm read supply current full resolution 4:3 ? 30 fps ? 5 10 ma full resolution 16:9 ? 30 fps ? 5 10 ma 1080p, 30 fps ? 6 10 ma 720p, 60 fps ? 5 10 ma vga, 60 fps ? 5 10 ma i dd _io i/o supply current full resolution 4:3 ? 30 fps ? 0.02 0.03 ma full resolution 16:9 ? 30 fps ? 0.02 0.03 ma 1080p, 30 fps ? 0.03 0.03 ma 720p, 60 fps ? 0.02 0.03 ma vga, 60 fps ? 0.02 0.03 ma i dd _1v2 digital supply current full resolution 4:3 ? 30 fps ? 105 130 ma full resolution 16:9 ? 30 fps ? 93 115 ma 1080p, 30 fps ? 53 110 ma 720p, 60 fps ? 75 90 ma vga, 60 fps ? 75 90 ma
ar0833 www. onsemi.com 41 table 24. typical operating current consumption (mipi) (continued) (nominal voltages: f extclk = 24 mhz; v aa = 2.8 v; v aa _pix = 2.8 v; dv dd _1v8 = 1.8 v; v dd _io = 1.8 v; dvdd_1v2 = 1.2 v high voltages: f extclk = 24 mhz; v aa = 3.1 v; v aa _pix = 3.1 v; dv dd _1v8 = 1.9 v; v dd _io = 1.9 v; dv dd _1v2 = 1.3 v; t j = 25 c) symbol unit max typ min condition parameter phy supply current phy supply current full resolution 4:3 ? 30 fps ? 10 14 ma full resolution 16:9 ? 30 fps ? 8 11 ma 1080p, 30 fps ? 1 4 ma 720p, 60 fps ? 3 3 ma vga, 60 fps ? 1 2 ma absolute maximum ratings table 25. absolute max voltages symbol parameter condition min typ max v dd _1v2 digital/analog voltage ? 0.3 1.5 v dv dd _1v8 otpm ? 0.3 2.1 v v dd _io i/o digital voltage ? 0.3 3.5 v v aa analog voltage ? 0.3 3.5 v v aa _pix pixel supply voltage ? 0.3 3.5 v dv dd _1v2_phy mipi supply ? 0.3 1.5 v stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device function ality should not be assumed, damage may occur and reliability may be affected. mipi specification reference the sensor design and this documentation is based on the following mipi specifications: ? mipi alliance standard for csi ? 2 version 1.0 ? mipi alliance standard for d ? phy version 1.0
ar0833 www. onsemi.com 42 package dimensions clcc48 10x10 case 848aj issue o
ar0833 www. onsemi.com 43 on semiconductor and are trademarks of semiconductor components industries, llc dba on semiconductor or its subsidiaries i n the united states and/or other countries. on semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. a listing of on semiconductor?s product/patent coverage may be accessed at www.onsemi.com/site/pdf/patent ? marking.pdf . on semiconductor reserves the right to make changes without further notice to any products herein. on semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular pu rpose, nor does on semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without li mitation special, consequential or incidental damages. buyer is responsible for its products and applications using on semiconductor products, including compliance with all laws, regulatio ns and safety requirements or standards, regardless of any support or applications information provided by on semiconductor. ?typical? parameters which may be provided in on semicond uctor data sheets and/or specifications can and do vary in dif ferent applications and actual performance may vary over time. all operating parameters, including ?typicals? mus t be validated for each customer application by customer?s technical experts. on semiconductor does not convey any license under its patent rights nor the rights of others. on semiconduc tor products are not designed, intended, or authorized for use as a critical component in life support systems or any fda class 3 medical devices or medical devices with a same or si milar classification in a foreign jurisdiction or any devices intended for implantation in the human body. should buyer purchase or use on semiconductor products for any such unintended or unauthorized application, buyer shall indemnify and hold on semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, cost s, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized u se, even if such claim alleges that on semiconductor was negligent regarding the design or manufacture of the part. on semiconductor is an equal opportunity/affirmative action employer . this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5817 ? 1050 ar0833/d a ? pixhs is a trademark of semiconductor components industries, llc (scillc) or its subsidiaries in the united states and/or other countries. literature fulfillment : literature distribution center for on semiconductor 19521 e. 32nd pkwy, aurora, colorado 80011 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative ?

▲Up To Search▲

Price & Availability of AR0833CS3C12SUAA0-DP

	To Download AR0833CS3C12SUAA0-DP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .